1. Cześć Gość. Czy wiesz, że według analizy rynku urządzenia:

    • QNAP - stanowią 63% rynku,
    • Synology i pozostali - tylko 37% rynku?

    To forum przeglądasz dzięki sponsorowi - firmie QNAP oraz zespołowi QNAP Club Polska.

Kompatybilne tunery dvb-t

Dyskusja w 'VideoStation' rozpoczęta przez użytkownika Terminator007, 11 Wrzesień 2012.

Ładowanie...
  1. Stanley99
    Offline

    Stanley99 Network Architect Q's Professional

    Dołączył:
    26 Listopad 2013
    Wiadomości:
    466
    Local Time:
    15:36
    Oceny:
    +3 / 0 / -0
    Followers:
    0
    Synology:
    DS214play
    O ile pamiętam z moich grudniowych testów: w ten sposób zgłaszał się w "Centrum informacji" tuner na IT9135 v.01
    A co :
    - po restarcie NAS-a ?
    - wyjęciu/włożeniu sticka do portu USB ?
    - melduje komenda dmesg ? (czy widać inicjalizację tunera, sterowników, itp.)
    Ewentualnie sprawdzić tuner na jego oryginalnych sterownikach/sofcie pod Windą - po prostu czy w ogóle działa...
     
  2. orcad
    Offline

    orcad Nowy użytkownik Beginner

    Dołączył:
    29 Grudzień 2014
    Wiadomości:
    17
    Miejscowość:
    Bielsko-Biała
    Local Time:
    15:36
    Oceny:
    +1 / 0 / -0
    Followers:
    0
    QNAP:
    null
    Synology:
    DS412+
    Ethernet:
    10 Mbps
    null 10 Mbps
    Dziękuje za odpowiedz !

    A wiec restartowałem parę razy i nic ! , kartę sprawdziłem pod Windowsem działa !!! , najlepsze ze dmesg meldował inicjacje kary na USB
    niby wszystko ok a nie ok :) , myślę sobie co tu zrobić dalej ? , wyciągałem dysk zamontowałem inny zainstalowałem świeży system i ruszyła karta :)
    była widoczna :) super , wiec postanowiłem włożyć ten poprzedni , i znowu nic !!!!! , za którymś wyłączeniem (użyłem opcji wyłącz ) \pojawiła wie w końcu karta na USB , wszystko super !!!!! , ale pozostaje pytanie czy te oprogramowanie jest aż tak stabilne jak się mówi czy karta TV nie jest testowana i rekomendowana przez Synology !! , przed DS412+ złożyłem sobie prostego NAS na płycie z procesorze atom wszystko chodziło pod linux Slackware 13.0 , przez 4 lata do padu dysku był to zwykły WD Blue a chodził 24 godziny na dobę żadnych problemów nie było , zaniki napięcia restarty itp. zero problemów porostu zapomniałem ze on instytucje , a tu niby firma która specjalizuje się w takich rozwiązaniach a tu takie dziwne problemy !!!!!! , tak czy siak BARDZO DZIĘKUJĘ ZA ODPOWIEDZ i PODPOWIEDZ:)
     
  3. Oliverek
    Offline

    Oliverek Nowy użytkownik Beginner

    Dołączył:
    2 Czerwiec 2014
    Wiadomości:
    19
    Local Time:
    15:36
    Oceny:
    +1 / 0 / -0
    Followers:
    0
    QNAP:
    null
    Synology:
    DS713+
    Ethernet:
    1 GbE
    null 1 GbE
    Kupiłem na tej samej stronie ten sam tuner i niestety po podłączeniu mój Synek go nie widzi :-( po podłączeniu wchodzę w VS i tam w Nagrywanie i prosi mnie o podłączenie kompatybilnego tunera :/
    Mam 713+ i próbowałem jednego portu z tyłu (w drugim podłączony dysk 2TB WD) i z przodu do USB Copy i nic :/ a w komputerze się zainstalował i jest wykrywalny...
    Synek był uruchamiany ponownie i tez nic nie pomogło

    Ma ktoś jakieś sugestie?
     
  4. Stanley99
    Offline

    Stanley99 Network Architect Q's Professional

    Dołączył:
    26 Listopad 2013
    Wiadomości:
    466
    Local Time:
    15:36
    Oceny:
    +3 / 0 / -0
    Followers:
    0
    Synology:
    DS214play
    Hm, co widać w :
    - Panelu Sterowania->Centrum informacji (u mnie: "Urządzenie USB: DK DVB-T Dongle - Dexatek Technology Ltd.")
    - poleceniu dmesg ? (czy widać incjalizację tunera, sterowników)
    Patrz dla porównania post TUTAJ
     
  5. Oliverek
    Offline

    Oliverek Nowy użytkownik Beginner

    Dołączył:
    2 Czerwiec 2014
    Wiadomości:
    19
    Local Time:
    15:36
    Oceny:
    +1 / 0 / -0
    Followers:
    0
    QNAP:
    null
    Synology:
    DS713+
    Ethernet:
    1 GbE
    null 1 GbE
    - w Panelu sterowania mam to samo - (DK DVB-T Dongle - Dexatek Technology Ltd.)
    - w poleceniu dmesg wykazało mi:

    Kod (Text):
    1. [   90.382760] usb 6-2: dvb_usb_v2: found a 'Dexatek DK DVB-T Dongle' in warm state
    2. [   90.430508] usb 6-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
    3. [   90.439898] DVB: registering new adapter (Dexatek DK DVB-T Dongle)
    4. [   90.449258] usb 6-2: DVB: registering adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))...
    5. [   90.457436] fc0013: Fitipower FC0013 successfully attached.
    6. [   90.480980] usb 6-2: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully initialized and connected
    7. [   90.489974] usbcore: registered new interface driver dvb_usb_rtl28xxu
    8. [   93.808808] synodtvd[15354]: segfault at 0 ip 00000000f6ae4610 sp 00000000ffb0d550 error 4 in libvideostation.so.0[f6acb000+28000]
    9. [  118.794385] warning: `named' uses 32-bit capabilities (legacy support in use)
    10. [  273.630478] usb 6-2: USB disconnect, device number 3
    11. [  273.636643] usb 6-2: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully deinitialized and disconnected
    12. [  273.947436] usbcore: deregistering interface driver dvb_usb_rtl28xxu
    13. [  875.618673] usb 6-2: new high-speed USB device number 4 using ehci_hcd
    14. [  875.779830] usbip 6-2:1.0: Enter
    15. [  875.779836] usbip 6-2:1.0: 6-2 is not in match_busid table... skip!
    16. [  875.788073] usbip 6-2:1.1: Enter
    17. [  875.788078] usbip 6-2:1.1: 6-2 is not in match_busid table... skip!
    18. [  876.144206] usb 6-2: dvb_usb_v2: found a 'Dexatek DK DVB-T Dongle' in warm state
    19. [  876.191869] usb 6-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
    20. [  876.201250] DVB: registering new adapter (Dexatek DK DVB-T Dongle)
    21. [  876.210610] usb 6-2: DVB: registering adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))...
    22. [  876.218758] fc0013: Fitipower FC0013 successfully attached.
    23. [  876.242212] usb 6-2: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully initialized and connected
    24. [  876.251234] usbcore: registered new interface driver dvb_usb_rtl28xxu
    25. [  918.877545] usb 6-2: USB disconnect, device number 4
    26. [  918.883191] usb 6-2: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully deinitialized and disconnected
    27. [  919.169539] usbcore: deregistering interface driver dvb_usb_rtl28xxu
    28. [  942.035213] usb 7-1: new high-speed USB device number 3 using etxhci_hcd_141015
    29. [  942.075728] usbip 7-1:1.0: Enter
    30. [  942.075735] usbip 7-1:1.0: 7-1 is not in match_busid table... skip!
    31. [  942.083982] usbip 7-1:1.1: Enter
    32. [  942.083988] usbip 7-1:1.1: 7-1 is not in match_busid table... skip!
    33. [  942.468349] usb 7-1: dvb_usb_v2: found a 'Dexatek DK DVB-T Dongle' in warm state
    34. [  942.518492] usb 7-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
    35. [  942.527842] DVB: registering new adapter (Dexatek DK DVB-T Dongle)
    36. [  942.537602] usb 7-1: DVB: registering adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))...
    37. [  942.545878] fc0013: Fitipower FC0013 successfully attached.
    38. [  942.571359] usb 7-1: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully initialized and connected
    39. [  942.580388] usbcore: registered new interface driver dvb_usb_rtl28xxu
    40. [ 3299.596050] tun: Universal TUN/TAP device driver, 1.6
    41. [ 3299.601266] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    42. [285605.274468] usb 7-1: USB disconnect, device number 3
    43. [285605.280342] usb 7-1: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully deinitialized and disconnected
    44. [285606.250213] usbcore: deregistering interface driver dvb_usb_rtl28xxu
    45. [285609.890177] usb 7-1: new high-speed USB device number 4 using etxhci_hcd_141015
    46. [285609.930721] usbip 7-1:1.0: Enter
    47. [285609.930728] usbip 7-1:1.0: 7-1 is not in match_busid table... skip!
    48. [285609.939082] usbip 7-1:1.1: Enter
    49. [285609.939089] usbip 7-1:1.1: 7-1 is not in match_busid table... skip!
    50. [285610.893581] usb 7-1: dvb_usb_v2: found a 'Dexatek DK DVB-T Dongle' in warm state
    51. [285610.943349] usb 7-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
    52. [285610.952819] DVB: registering new adapter (Dexatek DK DVB-T Dongle)
    53. [285610.962717] usb 7-1: DVB: registering adapter 0 frontend 0 (Realtek RTL2832(DVB-T))...
    54. [285610.970990] fc0013: Fitipower FC0013 successfully attached.
    55. [285610.996062] usb 7-1: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully initialized and connected
    56. [285611.005307] usbcore: registered new interface driver dvb_usb_rtl28xxu
    57.  
    tylko nic z tego nie rozumiem :/
     
  6. Stanley99
    Offline

    Stanley99 Network Architect Q's Professional

    Dołączył:
    26 Listopad 2013
    Wiadomości:
    466
    Local Time:
    15:36
    Oceny:
    +3 / 0 / -0
    Followers:
    0
    Synology:
    DS214play
    Heh, ja też niewiele ;) Ale widać, że system coś tam wykrywa, inicjalizuje, rejestruje. U mnie fragment, w którym pojawia się coś związanego z tunerem wygląda tak:
    Kod (Text):
    1.  
    2. [   67.523178] usb 1-1.5: dvb_usb_v2: found a 'Dexatek DK DVB-T Dongle' in warmstate
    3. [   67.573217] usb 1-1.5: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
    4. [   67.583506] DVB: registering new adapter (Dexatek DK DVB-T Dongle)
    5. [   67.593367] usb 1-1.5: DVB: registering adapter 0 frontend 0 (Realtek RTL2832(DVB-T))...
    6. [   67.601908] fc0013: Fitipower FC0013 successfully attached.
    7. [   67.627523] usb 1-1.5: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully initialized and connected
    8. [   67.636693] usbcore: registered new interface driver dvb_usb_rtl28xxu
    9.  
    Tylko zauważyłem, że u Ciebie po pewnym czasie następuje jakby deinicjalizacja:
    Kod (Text):
    1.  
    2. [  273.630478] usb 6-2: USB disconnect, device number 3
    3. [  273.636643] usb 6-2: dvb_usb_v2: 'Dexatek DK DVB-T Dongle' successfully deinitialized and disconnected
    4. [  273.947436] usbcore: deregistering interface driver dvb_usb_rtl28xxu
    5.  
    Potem z powrotem znajduje:
    Kod (Text):
    1.  
    2. [  876.144206] usb 6-2: dvb_usb_v2: found a 'Dexatek DK DVB-T Dongle' in warm state
    3. [  876.191869] usb 6-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
    4. [  876.201250] DVB: registering new adapter (Dexatek DK DVB-T Dongle)
    5.  
    Odłączałeś i podłączałes tuner na porcie USB?

    Tak poza tym w dmesg oraz w Panelu sterowania uważam wszystko wydaje się ok. Jeśli tunera nadal nie widać w VS, nie wiem co Ci poradzić. Odinstalować/zainstalować pakiet? Support? Może ktoś ma jeszcze jakiś pomysł?

    Pozdrawiam.

    EDIT
    Ale to zauważyłem dopiero teraz, po napisaniu postu:
    Kod (Text):
    1.  
    2. [   93.808808] synodtvd[15354]: segfault at 0 ip 00000000f6ae4610 sp 00000000ffb0d550 error 4 in libvideostation.so.0[f6acb000+28000]
    3.  
    Nie znam się na tym, ale error nigdy nie wróży nic dobrego, wygląda mi na jakiś błąd w Videostation! (plikach, bibliotekach?). Może jakiś guru od linuxa wyjaśni o co biega? Może pomoże przeinstalowanie VS?
     
  7. Yaaro
    Offline

    Yaaro System Engineer Q Specialist

    Dołączył:
    21 Listopad 2012
    Wiadomości:
    197
    Local Time:
    15:36
    Oceny:
    +1 / 0 / -0
    Followers:
    0
    Synology:
    DS214play
    VS 1.5 0754 Cabletech URZ0085 znów działa.
     
  8. wojtek_gtx
    Offline

    wojtek_gtx Entry Technician Q Associate

    Dołączył:
    17 Listopad 2014
    Wiadomości:
    44
    Miejscowość:
    Warszawa
    Local Time:
    18:36
    Oceny:
    +4 / 0 / -0
    Followers:
    0
    QNAP:
    null
    Synology:
    DS212
    Ethernet:
    1 GbE
    null 1 GbE
    A u mnie wszystko działało super po aktualizacji przestał streamować programy ale po ostaniej znowu zaczęło działać aż tu wczoraj po restarcie synka Video Station przestał widzieć tuner ... i nie wiem już co zrobić
     
  9. Yaaro
    Offline

    Yaaro System Engineer Q Specialist

    Dołączył:
    21 Listopad 2012
    Wiadomości:
    197
    Local Time:
    15:36
    Oceny:
    +1 / 0 / -0
    Followers:
    0
    Synology:
    DS214play
    Próbowałeś restart z "palca"? U mnie czasami pomaga.
     
  10. wojtek_gtx
    Offline

    wojtek_gtx Entry Technician Q Associate

    Dołączył:
    17 Listopad 2014
    Wiadomości:
    44
    Miejscowość:
    Warszawa
    Local Time:
    18:36
    Oceny:
    +4 / 0 / -0
    Followers:
    0
    QNAP:
    null
    Synology:
    DS212
    Ethernet:
    1 GbE
    null 1 GbE
    Robiłem restart softowy, z palca i na gorąco - żadna opcja nie pomogła ... odinstalowałem Video Station i zainstalowałem ponownie tez nie pomogło. Już nie wiem co zrobić może firma synology zaostrzyła kompatybilność tunerów że nie działają. Moja karta zgłasza się jako ZOLID Mini DVB-T Stick


    Kod (Text):
    1. Synology-DOM> dmesg
    2. [    0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #5565 Mon May 11 02:12:06 CST 2015
    3. [    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
    4. [    0.000000] CPU: VIVT data cache, VIVT instruction cache
    5. [    0.000000] Machine: Synology 6282 board
    6. [    0.000000] Using UBoot passing parameters structure
    7. [    0.000000] Sys Clk = 200000000, Tclk = 166666667
    8. [    0.000000] Synology Board ID: 27
    9. [    0.000000] Memory policy: ECC disabled, Data cache writeback
    10. [    0.000000] On node 0 totalpages: 65536
    11. [    0.000000] free_area_init_node: node 0, pgdat c03ed718, node_mem_map c0c01000
    12. [    0.000000]   Normal zone: 512 pages used for memmap
    13. [    0.000000]   Normal zone: 0 pages reserved
    14. [    0.000000]   Normal zone: 65024 pages, LIFO batch:15
    15. [    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 65024
    16. [    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212v10 ihd_num=2 netif_num=1
    17. [    0.000000] Synology Hardware Version: DS212v10-j
    18. [    0.000000] Internal HD num: 2
    19. [    0.000000] Internal netif num: 1
    20. [    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    21. [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    22. [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    23. [    0.000000] Memory: 256MB = 256MB total
    24. [    0.000000] Memory: 244992KB available (3632K code, 519K data, 124K init, 0K highmem)
    25. [    0.000000] Hierarchical RCU implementation.
    26. [    0.000000] NR_IRQS:128
    27. [    0.000000] Console: colour dummy device 80x30
    28. [    0.000000] Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
    29. [    0.240000] Mount-cache hash table entries: 512
    30. [    0.240000] CPU: Testing write buffer coherency: ok
    31. [    0.240000] devtmpfs: initialized
    32. [    0.240000] xor: measuring software checksum speed
    33. [    0.290000]    arm4regs  :  1448.800 MB/sec
    34. [    0.340000]    8regs     :   869.200 MB/sec
    35. [    0.390000]    32regs    :  1122.000 MB/sec
    36. [    0.390000] xor: using function: arm4regs (1448.800 MB/sec)
    37. [    0.390000] NET: Registered protocol family 16
    38. [    0.390000] Feroceon L2: Enabling L2
    39. [    0.390000] Feroceon L2: Cache support initialised, in WT override mode.
    40. [    0.410000]
    41. [    0.410000] CPU Interface
    42. [    0.410000] -------------
    43. [    0.410000] SDRAM_CS0 ....base 00000000, size 256MB
    44. [    0.410000] SDRAM_CS1 ....disable
    45. [    0.410000] SDRAM_CS2 ....disable
    46. [    0.410000] SDRAM_CS3 ....disable
    47. [    0.410000] PEX0_MEM ....base e0000000, size 128MB
    48. [    0.410000] PEX0_IO ....base f2000000, size   1MB
    49. [    0.410000] PEX1_MEM ....base e8000000, size 128MB
    50. [    0.410000] PEX1_IO ....base f2100000, size   1MB
    51. [    0.410000] INTER_REGS ....base f1000000, size   1MB
    52. [    0.410000] NFLASH_CS ....base fa000000, size   2MB
    53. [    0.410000] SPI_CS ....base f4000000, size  16MB
    54. [    0.410000] BOOT_ROM_CS ....no such
    55. [    0.410000] DEV_BOOTCS ....no such
    56. [    0.410000] CRYPT_ENG ....base f0000000, size   2MB
    57. [    0.410000]  Detected Tclk 200000000 and SysClk 533333333
    58. [    0.410000] Apply DS 212 GPIO
    59. [    0.410000] Synology 6282 1, 2 bay GPIO Init
    60. [    0.910000] PEX0 interface detected no Link.
    61. [    1.410000] PEX1 interface detected Link X1
    62. [    1.410000] PCI: bus0: Fast back to back transfers enabled
    63. [    1.410000] pci 0000:01:01.0: reg 10 64bit mmio: [0x98000000-0x98001fff]
    64. [    1.410000] pci 0000:01:01.0: PME# supported from D0 D3hot
    65. [    1.410000] pci 0000:01:01.0: PME# disabled
    66. [    1.410000] PCI: bus1: Fast back to back transfers disabled
    67. [    1.420000] bio: create slab <bio-0> at 0
    68. [    1.420000] vgaarb: loaded
    69. [    1.420000] SCSI subsystem initialized
    70. [    1.420000] libata version 3.00 loaded.
    71. [    1.590000] raid6: int32x1    126 MB/s
    72. [    1.760000] raid6: int32x2    185 MB/s
    73. [    1.930000] raid6: int32x4    180 MB/s
    74. [    2.100000] raid6: int32x8    193 MB/s
    75. [    2.100000] raid6: using algorithm int32x8 (193 MB/s)
    76. [    2.100000] Switching to clocksource kw_clocksource
    77. [    2.100000] NET: Registered protocol family 2
    78. [    2.100000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    79. [    2.100000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    80. [    2.100000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    81. [    2.100000] TCP: Hash tables configured (established 8192 bind 8192)
    82. [    2.100000] TCP reno registered
    83. [    2.100000] NET: Registered protocol family 1
    84. [    2.100000] RPC: Registered udp transport module.
    85. [    2.100000] RPC: Registered tcp transport module.
    86. [    2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
    87. [    2.100000] Trying to unpack rootfs image as initramfs...
    88. [    3.090000] rootfs image is not initramfs (no cpio magic); looks like an initrd
    89. [    3.110000] Freeing initrd memory: 4096K
    90. [    3.110000] XOR registered 4 channels
    91. [    3.110000] XOR 2nd invalidate WA enabled
    92. [    3.110000] VFS: Disk quotas dquot_6.5.2
    93. [    3.110000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    94. [    3.110000] msgmni has been set to 486
    95. [    3.110000] alg: No test for md5 (md5-generic)
    96. [    3.110000] alg: No test for des (des-generic)
    97. [    3.110000] alg: No test for des3_ede (des3_ede-generic)
    98. [    3.110000] alg: No test for stdrng (krng)
    99. [    3.110000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    100. [    3.110000] io scheduler noop registered
    101. [    3.110000] io scheduler anticipatory registered (default)
    102. [    3.110000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    103. [    3.120000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
    104. [    3.130000] console [ttyS0] enabled
    105. [    3.130000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
    106. [    3.140000] brd: module loaded
    107. [    3.140000] sata_mv sata_mv.0: version 1.28
    108. [    3.150000] sata_mv sata_mv.0: slots 32 ports 2
    109. [    3.150000] scsi0 : sata_mv
    110. [    3.160000] scsi1 : sata_mv
    111. [    3.160000] ata1: SATA max UDMA/133 irq 21
    112. [    3.160000] ata2: SATA max UDMA/133 irq 21
    113. [   10.930000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
    114. [   10.990000] ata1.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133
    115. [   10.990000] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
    116. [   11.060000] ata1.00: configured for UDMA/133
    117. [   11.080000] scsi 0:0:0:0: Direct-Access     WDC      WD5000AADS-00S9B0        01.0 PQ: 0 ANSI: 5
    118. [   11.080000] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
    119. [   11.090000] sd 0:0:0:0: [sda] Write Protect is off
    120. [   11.100000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    121. [   11.100000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    122. [   11.110000]  sda: sda1 sda2 sda3 < sda5 sda6 >
    123. [   11.140000] sd 0:0:0:0: [sda] Attached SCSI disk
    124. [   14.140000] Delay 5 seconds to wait for disk 2 ready.
    125. [   19.650000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
    126. [   19.690000] ata2.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133
    127. [   19.690000] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
    128. [   19.760000] ata2.00: configured for UDMA/133
    129. [   19.780000] scsi 1:0:0:0: Direct-Access     WDC      WD5000AADS-00S9B0        01.0 PQ: 0 ANSI: 5
    130. [   19.780000] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
    131. [   19.790000] sd 1:0:0:0: [sdb] Write Protect is off
    132. [   19.800000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    133. [   19.800000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    134. [   19.810000]  sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 >
    135. [   19.850000] sd 1:0:0:0: [sdb] Attached SCSI disk
    136. [   19.850000] physmap platform flash device: 00400000 at f8000000
    137. [   19.860000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
    138. [   19.870000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
    139. [   19.890000] 6 RedBoot partitions found on MTD device SYNOMTD-0
    140. [   19.900000] SYNOMTD flash bank 0: Using RedBoot partition definition
    141. [   19.900000] Creating 6 MTD partitions on "SYNOMTD-0":
    142. [   19.910000] 0x000000000000-0x000000080000 : "RedBoot"
    143. [   19.920000] 0x000000080000-0x000000280000 : "zImage"
    144. [   19.920000] 0x000000280000-0x0000003c0000 : "rd.gz"
    145. [   19.930000] 0x0000003c0000-0x0000003d0000 : "vendor"
    146. [   19.930000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
    147. [   19.940000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
    148. [   19.940000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
    149. [   19.950000] serial number='BAK3N03540'
    150. [   19.950000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
    151. [   19.960000] 0x0000003f0000-0x000000400000 : "FIS directory"
    152. [   19.970000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
    153. [   19.980000] cmdlinepart partition parsing not available
    154. [   19.980000] Loading Marvell Ethernet Driver:
    155. [   19.990000]   o Cached descriptors in DRAM
    156. [   19.990000]   o DRAM SW cache-coherency
    157. [   19.990000]   o 2 Giga ports supported
    158. [   20.000000]   o Single RX Queue support - ETH_DEF_RXQ=0
    159. [   20.000000]   o Single TX Queue support - ETH_DEF_TXQ=0
    160. [   20.010000]   o TCP segmentation offload (TSO) supported
    161. [   20.010000]   o Receive checksum offload supported
    162. [   20.020000]   o Transmit checksum offload supported
    163. [   20.020000]   o SKB Recycle supported - (Enabled)
    164. [   20.030000]   o Rx descripors: q0=128
    165. [   20.030000]   o Tx descripors: q0=532
    166. [   20.030000]   o Loading network interface(s):
    167. [   20.040000]     o  register under mv88fx_eth platform
    168. [   20.050000]     o eth0, ifindex = 2, GbE port = 0
    169. [   20.050000]     o eth0, phy chipid = 1410e90, Support WOL = 32
    170. [   20.060000]
    171. [   20.060000] md: linear personality registered for level -1
    172. [   20.060000] md: raid0 personality registered for level 0
    173. [   20.070000] md: raid1 personality registered for level 1
    174. [   20.070000] md: raid10 personality registered for level 10
    175. [   20.080000] md: raid6 personality registered for level 6
    176. [   20.080000] md: raid5 personality registered for level 5
    177. [   20.090000] md: raid4 personality registered for level 4
    178. [   20.100000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
    179. [   20.100000] cpuidle: using governor ladder
    180. [   20.110000] TCP cubic registered
    181. [   20.110000] NET: Registered protocol family 17
    182. [   20.120000] NET: Registered protocol family 15
    183. [   20.120000] registered taskstats version 1
    184. [   20.130000] md: Waiting for all devices to be available before autodetect
    185. [   20.130000] md: If you don't use raid, use raid=noautodetect
    186. [   20.140000] md: Autodetecting RAID arrays.
    187. [   20.180000] md: invalid raid superblock magic on sda5
    188. [   20.190000] md: sda5 does not have a valid v0.90 superblock, not importing!
    189. [   20.220000] md: invalid raid superblock magic on sda6
    190. [   20.220000] md: sda6 does not have a valid v0.90 superblock, not importing!
    191. [   20.270000] md: invalid raid superblock magic on sdb5
    192. [   20.280000] md: sdb5 does not have a valid v0.90 superblock, not importing!
    193. [   20.320000] md: invalid raid superblock magic on sdb6
    194. [   20.320000] md: sdb6 does not have a valid v0.90 superblock, not importing!
    195. [   20.330000] md: Scanned 8 and added 4 devices.
    196. [   20.340000] md: autorun ...
    197. [   20.340000] md: considering sda1 ...
    198. [   20.340000] md:  adding sda1 ...
    199. [   20.350000] md: sda2 has different UUID to sda1
    200. [   20.350000] md:  adding sdb1 ...
    201. [   20.350000] md: sdb2 has different UUID to sda1
    202. [   20.360000] md: created md0
    203. [   20.360000] md: bind<sdb1>
    204. [   20.360000] md: bind<sda1>
    205. [   20.370000] md: running: <sda1><sdb1>
    206. [   20.370000] raid1: raid set md0 active with 2 out of 2 mirrors
    207. [   20.380000] md0: detected capacity change from 0 to 2549940224
    208. [   20.380000] md: considering sda2 ...
    209. [   20.390000] md:  adding sda2 ...
    210. [   20.390000] md:  adding sdb2 ...
    211. [   20.390000] md: created md1
    212. [   20.400000] md: bind<sdb2>
    213. [   20.400000] md: bind<sda2>
    214. [   20.400000] md: running: <sda2><sdb2>
    215. [   20.400000] raid1: raid set md1 active with 2 out of 2 mirrors
    216. [   20.410000] md1: detected capacity change from 0 to 2147418112
    217. [   20.420000] md: ... autorun DONE.
    218. [   20.420000] RAMDISK: lzma image found at block 0
    219. [   21.490000] VFS: Mounted root (ext2 filesystem) on device 1:0.
    220. [   21.720000] usbcore: registered new interface driver usbfs
    221. [   21.720000] usbcore: registered new interface driver hub
    222. [   21.750000] usbcore: registered new interface driver ethub
    223. [   21.750000] usbcore: registered new device driver usb
    224. [   21.800000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    225. [   21.850000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    226. [   21.860000] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
    227. [   21.870000] orion-ehci orion-ehci.0: Marvell Orion EHCI
    228. [   21.870000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
    229. [   21.910000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
    230. [   21.930000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
    231. [   21.930000] usb usb1: configuration #1 chosen from 1 choice
    232. [   21.960000] hub 1-0:1.0: USB hub found
    233. [   21.960000] hub 1-0:1.0: 1 port detected
    234. [   22.060000] xhci_hcd 0000:01:01.0: xHCI Host Controller
    235. [   22.070000] xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 2
    236. [   22.080000] xhci_hcd 0000:01:01.0: irq 10, io mem 0xe8000000
    237. [   22.090000] usb usb2: No SuperSpeed endpoint companion for config 1  interface 0 altsetting 0 ep 129: using minimum values
    238. [   22.120000] usb usb2: configuration #1 chosen from 1 choice
    239. [   22.120000] xHCI xhci_add_endpoint called for root hub
    240. [   22.120000] xHCI xhci_check_bandwidth called for root hub
    241. [   22.120000] hub 2-0:1.0: USB hub found
    242. [   22.120000] hub 2-0:1.0: 4 ports detected
    243. [   22.250000] ds212_synobios: module license 'Synology Inc.' taints kernel.
    244. [   22.250000] Disabling lock debugging due to kernel taint
    245. [   22.310000] correction with 0x0f
    246. [   22.360000] 2015-5-25 6:59:26 UTC
    247. [   22.370000] synobios: load, major number 201
    248. [   22.370000] Brand: Synology
    249. [   22.370000] Model: DS-212
    250. [   22.380000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
    251. [   22.380000] synobios cpu_arch proc entry initialized
    252. [   22.390000] synobios crypto_hw proc entry initialized
    253. [   22.390000] synobios syno_platform proc entry initialized
    254. [   22.400000] usb 1-1: new high speed USB device using orion-ehci and address 2
    255. [   22.430000] synobios: unload
    256. [   22.540000]  md0: unknown partition table
    257. [   22.570000] Got empty serial number. Generate serial number from product.
    258. [   22.580000] usb 1-1: configuration #1 chosen from 1 choice
    259. [   22.580000] hub 1-1:1.0: USB hub found
    260. [   22.610000] hub 1-1:1.0: 4 ports detected
    261. [   24.690000] usb 2-3: new low speed USB device using xhci_hcd and address 2
    262. [   24.760000] usb 2-3: configuration #1 chosen from 1 choice
    263. [   24.760000] usb 2-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    264. [   24.870000] usb 1-1.3: new high speed USB device using orion-ehci and address 3
    265. [   25.080000] Got empty serial number. Generate serial number from product.
    266. [   25.090000] usb 1-1.3: configuration #1 chosen from 1 choice
    267. [   25.190000] usb 1-1.4: new high speed USB device using orion-ehci and address 4
    268. [   25.310000] usb 1-1.4: configuration #1 chosen from 1 choice
    269. [   25.400000] EXT4-fs (md0): barriers disabled
    270. [   25.410000] EXT4-fs (md0): mounted filesystem with ordered data mode
    271. [   27.890000] EXT3-fs: md0: couldn't mount because of unsupported optional features (240).
    272. [   27.890000] EXT2-fs: md0: couldn't mount because of unsupported optional features (240).
    273. [   27.900000] EXT4-fs (md0): barriers disabled
    274. [   27.910000] EXT4-fs (md0): mounted filesystem with ordered data mode
    275. [   27.920000] VFS: Mounted root (ext4 filesystem) on device 9:0.
    276. [   27.920000] Trying to move old root to /initrd ... okay
    277. [   27.930000] Freeing init memory: 124K
    278. [   33.110000] sd 0:0:0:0: Attached scsi generic sg0 type 0
    279. [   33.110000] sd 1:0:0:0: Attached scsi generic sg1 type 0
    280. [   33.570000]  md1: unknown partition table
    281. [   33.640000] Adding 2097080k swap on /dev/md1.  Priority:-1 extents:1 across:2097080k
    282. [   34.300000] init: syno-auth-check main process (1123) killed by TERM signal
    283. [   35.340000] NET: Registered protocol family 10
    284. [   35.350000] lo: Disabled Privacy Extensions
    285. [   35.420000] <30>systemd-udevd[1271]: starting version 204
    286. [   36.460000] IPv6 over IPv4 tunneling driver
    287. [   36.470000] sit0: Disabled Privacy Extensions
    288. [   40.690000] cpufreq: Init kirkwood cpufreq driver
    289. [   40.700000] cpufreq: High frequency: 1600000KHz - Low frequency: 533333KHz
    290. [   42.940000] alg: No test for aes (aes-generic)
    291. [   43.080000] alg: No test for stdrng (ansi_cprng)
    292. [   43.250000] alg: No test for crc32c (crc32c-generic)
    293. [   43.700000] cesadev_init(bf18e000)
    294. [   43.740000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
    295. [   43.820000] alg: No test for sha1 (sha1-generic)
    296. [   43.850000] alg: No test for sha224 (sha224-generic)
    297. [   43.860000] alg: No test for sha256 (sha256-generic)
    298. [   43.890000] alg: No test for sha384 (sha384-generic)
    299. [   43.900000] alg: No test for sha512 (sha512-generic)
    300. [   43.960000] encryptfs using the OCF package.
    301. [   44.260000] alg: No test for arc4 (arc4-generic)
    302. [   44.390000] fuse init (API version 7.13)
    303. [   44.670000] sky2 driver version 1.25
    304. [   44.780000] correction with 0x0f
    305. [   44.830000] 2015-5-25 6:59:48 UTC
    306. [   44.830000] synobios: load, major number 201
    307. [   44.840000] Brand: Synology
    308. [   44.840000] Model: DS-212
    309. [   44.840000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
    310. [   44.850000] synobios cpu_arch proc entry initialized
    311. [   44.860000] synobios crypto_hw proc entry initialized
    312. [   44.860000] synobios syno_platform proc entry initialized
    313. [   46.690000] ip_tables: (C) 2000-2006 Netfilter Core Team
    314. [   46.920000] nf_conntrack version 0.5.0 (3897 buckets, 15588 max)
    315. [   47.530000] ip6_tables: (C) 2000-2006 Netfilter Core Team
    316. [   48.820000] eth0: mac address changed
    317. [   50.970000] eth0: link down
    318. [   50.970000] eth0: started
    319. [   52.070000] eth0: link up, full duplex, speed 1 Gbps
    320. [   53.320000] usb 2-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    321. [   55.520000] ADDRCONF(NETDEV_UP): eth0: link is not ready
    322. [   55.530000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    323. [   72.580000] md: md3 stopped.
    324. [   72.650000] md: bind<sda6>
    325. [   72.650000] md: bind<sdb6>
    326. [   72.710000] raid1: raid set md3 active with 2 out of 2 mirrors
    327. [   72.710000] md3: detected capacity change from 0 to 249940344832
    328. [   72.920000]  md3: unknown partition table
    329. [   73.150000] md: md2 stopped.
    330. [   73.170000] md: bind<sdb5>
    331. [   73.180000] md: bind<sda5>
    332. [   73.230000] raid1: raid set md2 active with 2 out of 2 mirrors
    333. [   73.240000] md2: detected capacity change from 0 to 245210808320
    334. [   73.520000]  md2: unknown partition table
    335. [   82.690000] EXT4-fs (dm-0): barriers disabled
    336. [   82.720000] usb 2-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    337. [   86.650000] EXT4-fs (dm-0): recovery complete
    338. [   86.650000] EXT4-fs (dm-0): mounted filesystem with writeback data mode
    339. [   90.320000] ata1.00: configured for UDMA/133
    340. [   90.320000] ata1: EH complete
    341. [   90.360000] ata2.00: configured for UDMA/133
    342. [   90.360000] ata2: EH complete
    343. [   90.710000] Initializing USB Mass Storage driver...
    344. [   90.840000] scsi2 : SCSI emulation for USB Mass Storage devices
    345. [   90.870000] usbcore: registered new interface driver usb-storage
    346. [   90.870000] USB Mass Storage support registered.
    347. [   90.880000] usb-storage: device found at 4
    348. [   90.880000] usb-storage: waiting for device to settle before scanning
    349. [   91.030000] usbcore: registered new interface driver usblp
    350. [   91.420000] usbcore: registered new interface driver hiddev
    351. [   91.420000] usbcore: registered new interface driver usbhid
    352. [   91.430000] usbhid: v2.6:USB HID core driver
    353. [   95.080000] ata1.00: configured for UDMA/133
    354. [   95.080000] ata1: EH complete
    355. [   95.400000] ata2.00: configured for UDMA/133
    356. [   95.400000] ata2: EH complete
    357. [   95.900000] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE           9910 PQ: 0 ANSI: 0
    358. [   95.910000] sd 2:0:0:0: Attached scsi generic sg2 type 0
    359. [   95.930000] sd 2:0:0:0: [sdq] Attached SCSI removable disk
    360. [   95.950000] scsi 2:0:0:1: Direct-Access     Generic  STORAGE DEVICE           9910 PQ: 0 ANSI: 0
    361. [   95.960000] sd 2:0:0:1: Attached scsi generic sg3 type 0
    362. [   95.970000] sd 2:0:0:1: [sdr] Attached SCSI removable disk
    363. [   95.990000] usb-storage: device scan complete
    364. [   97.330000] loop: module loaded
    365. [   99.400000] Slow work thread pool: Starting up
    366. [  100.150000] Slow work thread pool: Ready
    367. [  115.210000] init: gcpd main process (8981) terminated with status 255
    368. [  115.220000] init: gcpd main process ended, respawning
    369. [  115.550000] init: gcpd main process (8996) terminated with status 255
    370. [  115.550000] init: gcpd main process ended, respawning
    371. [  115.990000] init: gcpd main process (9017) terminated with status 255
    372. [  115.990000] init: gcpd main process ended, respawning
    373. [  117.050000] init: gcpd main process (9044) terminated with status 255
    374. [  117.080000] init: gcpd main process ended, respawning
    375. [  117.660000] init: gcpd main process (9060) terminated with status 255
    376. [  117.660000] init: gcpd main process ended, respawning
    377. [  118.290000] init: gcpd main process (9087) terminated with status 255
    378. [  118.290000] init: gcpd respawning too fast, stopped
    379. [  131.160000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
    380. [  188.370000] PPP generic driver version 2.4.2
    381. [  188.500000] alg: No test for ecb(arc4) (ecb(arc4-generic))
    382. [  188.510000] PPP MPPE Compression module registered
    383. [  188.550000] PPP BSD Compression module registered
    384. [  188.630000] PPP Deflate Compression module registered
    385. [  226.690000] usbcore: registered new interface driver snd-usb-audio
    386. [  226.970000] usbcore: registered new interface driver snd-usb-hiface
    387. [  287.840000] init: winbindd main process (8892) killed by TERM signal
    388. [  287.940000] init: smbd main process (8998) killed by TERM signal
    389. [ 8108.910000] init: winbindd main process (15799) killed by TERM signal
    390. [ 8109.070000] init: smbd main process (16071) killed by TERM signal
    391. [30111.730000] init: winbindd main process (6382) killed by TERM signal
    392. [30111.980000] init: smbd main process (6506) killed by TERM signal
    393. [46979.200000] usb 1-1.3: USB disconnect, address 3
    394. [46986.160000] usb 2-3: USB disconnect, address 2
    395. [46995.290000] usb 2-3: new high speed USB device using xhci_hcd and address 3
    396. [46995.310000] Got empty serial number. Generate serial number from product.
    397. [46995.320000] usb 2-3: configuration #1 chosen from 1 choice
    398. [47002.970000] usb 2-4: new low speed USB device using xhci_hcd and address 4
    399. [47005.100000] usb 2-4: configuration #1 chosen from 1 choice
    400. [47005.100000] usb 2-4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    401. [47006.620000] usb 2-4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    402. [47015.030000] usb 1-1.3: new high speed USB device using orion-ehci and address 5
    403. [47015.140000] usb 1-1.3: configuration #1 chosen from 1 choice
    404. [47015.160000] scsi3 : SCSI emulation for USB Mass Storage devices
    405. [47015.170000] usb-storage: device found at 5
    406. [47015.170000] usb-storage: waiting for device to settle before scanning
    407. [47020.190000] scsi 3:0:0:0: Direct-Access     TOSHIBA  MK1059GSM                     PQ: 0 ANSI: 2 CCS
    408. [47020.200000] sd 3:0:0:0: Attached scsi generic sg4 type 0
    409. [47020.210000] usb-storage: device scan complete
    410. [47020.210000] sd 3:0:0:0: [sds] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    411. [47020.220000] sd 3:0:0:0: [sds] Write Protect is off
    412. [47020.220000] sd 3:0:0:0: [sds] Mode Sense: 28 00 00 00
    413. [47020.220000] sd 3:0:0:0: [sds] Assuming drive cache: write through
    414. [47020.240000] sd 3:0:0:0: [sds] Assuming drive cache: write through
    415. [47020.240000]  sds: sds1
    416. [47020.290000] sd 3:0:0:0: [sds] Assuming drive cache: write through
    417. [47020.290000] sd 3:0:0:0: [sds] Attached SCSI disk
    418. [47134.810000] sd 2:0:0:0: [sdq] 131072000 512-byte logical blocks: (67.1 GB/62.5 GiB)
    419. [47134.820000] sd 2:0:0:0: [sdq] Assuming drive cache: write through
    420. [47134.830000] sd 2:0:0:0: [sdq] Assuming drive cache: write through
    421. [47134.830000]  sdq: sdq1
    422. [79304.300000] init: winbindd main process (28205) killed by TERM signal
    423. [79305.040000] init: smbd main process (28061) killed by TERM signal
    424. Synology-DOM>
    425.  
     
  11. przemodd84
    Offline

    przemodd84 Entry Technician Q Associate

    Dołączył:
    6 Marzec 2015
    Wiadomości:
    49
    Local Time:
    15:36
    Oceny:
    +3 / 0 / -0
    Followers:
    0
    Synology:
    DS115
  12. Canis
    Offline

    Canis Nowy użytkownik Noobie

    Dołączył:
    23 Styczeń 2014
    Wiadomości:
    15
    Local Time:
    15:36
    Oceny:
    +0 / 0 / -0
    Followers:
    0
    Synology:
    DS112+
    PCTv nanoStick DVB-T 73e na DS214play działa bezproblemowo

    Wysłane z mojego GT-N7100 przy użyciu Tapatalka
     
  13. Tomu
    Offline

    Tomu Nowy użytkownik Noobie

    Dołączył:
    11 Październik 2013
    Wiadomości:
    17
    Local Time:
    15:36
    Oceny:
    +0 / 0 / -0
    Followers:
    0
    Synology:
    DS213air
    PCTV Pico stick 74e - Działa z Videostation - TVHEADEND - jest widoczny testy trwają, DVBLogic jest widoczny - testy trwają (Synology 213AIR)
     
  14. jools
    Offline

    jools Nowy użytkownik Noobie

    Dołączył:
    18 Listopad 2010
    Wiadomości:
    28
    Local Time:
    16:36
    Oceny:
    +0 / 0 / -0
    Followers:
    0
    Trochę czasu minęło już... Macie może sprawdzone jakieś tunery, które aktualnie można znaleźć w sklepach ?
     
  15. wojtek_gtx
    Offline

    wojtek_gtx Entry Technician Q Associate

    Dołączył:
    17 Listopad 2014
    Wiadomości:
    44
    Miejscowość:
    Warszawa
    Local Time:
    18:36
    Oceny:
    +4 / 0 / -0
    Followers:
    0
    QNAP:
    null
    Synology:
    DS212
    Ethernet:
    1 GbE
    null 1 GbE
    Ja mam trzy sztuki w domu:
    1. Manta DVBTUSB01
    2. Omega T300 - kupiony w Carrefour
    3. Pinacle PCTV 73e SE

    Wszystkie trzy pracują wyśmienicie na DSM 5 jak i na DSM 6 tyle że to wszystko tylko DVB-T, a sam teraz poszukuję czegoś tyle że z DVB-T2.
    Jeżeli by ktoś miał jakiś sprawdzony tuner z DVB-T2 do synology był bym wdzięczny.
     

Użytkownicy znaleźli te stronę szukając słów:

  1. kamilaloch loc:PL

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Odrzuć powiadomienie.